PROTOTYPE ALAT PENGERING SEPATU BERBASIS ARDUINO UNTUK MENUNJANG USAHA CUCI SEPATU SUKLIN.ID
Abstract
The growth of shoe cleaning service businesses requires technological innovation to improve operational effectiveness, particularly in the drying process which still depends on weather conditions, resulting in unstable processing time and reduced productivity. This study aims to design and implement an Arduino-based shoe dryer prototype that operates automatically, safely, and efficiently to support the operations of the Suklin.id shoe cleaning business. The research employed the waterfall method, consisting of requirement, design, implementation, verification, and maintenance stages. The system was built using Arduino Uno as the main microcontroller, a DHT11 sensor for temperature and humidity detection, a PTC heater and incandescent lamp as heat sources, a fan for air circulation, a relay as an actuator controller, and a limit switch with a buzzer as a door safety system. An automatic safety mechanism disconnects the power supply when the temperature exceeds the set threshold. Testing results show that the prototype dried canvas shoes at an average temperature of 35.8°C within 1 hour 39 minutes, and synthetic leather shoes at 32.2°C within 1 hour 15 minutes. Compared with the conventional method, the system achieved a time efficiency of 72.50% for canvas shoes and 68.75% for synthetic leather shoes. The developed prototype is therefore proven to improve drying efficiency and reduce dependency on weather conditions.
Downloads
References
A. B. Rizkianto, "Rancang bangun pengering sepatu berdasarkan kelembaban menggunakan metode PID," Tugas Akhir, Institut Bisnis dan Informatika Stikom Surabaya, Surabaya, 2019.
B. Baskaran, M. Mukramin, and B. Sulaeman, "Rancang bangun sistem pengering sepatu otomatis menggunakan sensor kelembaban suhu berbasis Arduino," Jurnal Informatika dan Teknik Elektro Terapan, vol. 12, no. 3S1, 2024, doi: 10.23960/jitet.v12i3S1.5253.
F. J. Nugraha, "Pengembangan alat pengering sepatu otomatis berbasis Arduino dengan kontrol PID," Skripsi, Institut Teknologi Nasional Malang, Malang, 2019.
F. Q. Afandi, A. Bachri, and U. Ilmi, "Prototype kotak menjaga kekeringan dan kelembaban sepatu berbasis mikrokontroller," SinarFe7, vol. 3, no. 1, 2020.
Y. Mulyanto and Y. Karisma, "Rancang bangun sistem monitoring perkembangan anak di TKIT Taamasa menggunakan metode spiral," Jurnal Informatika Teknologi dan Sains (Jinteks), vol. 2, no. 3, pp. 190-195, 2020, doi: 10.51401/jinteks.v2i3.754.
A. Syarifudin and N. Ani, "Rancangan sistem informasi pengajuan dan pelaporan tunjangan kinerja Kementerian Keuangan menggunakan metode prototype," Jurnal Sisfokom, vol. 8, no. 2, pp. 149-158, 2019, doi: 10.32736/sisfokom.v8i2.641.
I. Parito and N. G. Djuni, "Rancang bangun tongkat pintar tunanetra berbasis mikrokontroler," Jurnal SPEKTRUM, vol. 8, no. 1, 2021.
R. Aulia, R. A. Fauzan, and I. Lubis, "Pengendalian suhu ruangan menggunakan FAN dan DHT11 berbasis Arduino," CESS (Journal of Computer Engineering, System and Science), vol. 6, no. 1, p. 30, 2021, doi: 10.24114/cess.v6i1.21113.
M. Saleh and M. Haryanti, "Rancang bangun sistem keamanan rumah menggunakan relay," Jurnal Teknologi Elektro, vol. 8, no. 2, p. 143398, 2017, doi: 10.22441/jte.v8i2.1601.
D. Siswanto, "Jemuran pakaian otomatis menggunakan sensor hujan dan sensor LDR berbasis Arduino Uno," e-NARODROID, vol. 1, no. 2, 2015, doi: 10.31090/narodroid.v1i2.69.
Y. Darnita, A. Discrise, and R. Toyib, "Prototype alat pendeteksi kebakaran menggunakan Arduino," Jurnal Informatika Upgris, vol. 7, no. 1, 2021, doi: 10.26877/jiu.v7i1.7094.
D. D. Tahiru, V. C. Poekoel, F. D. Kambey, and R. F. Robot, "Karakteristik performansi suhu ruangan pengering hibrida pada proses pengeringan bawang merah," Jurnal Teknik Elektro dan Komputer, vol. 8, no. 2, pp. 43-50, 2019, doi: 10.35793/jtek.v8i2.23911.
P. E. S. Dita, A. Al Fahrezi, P. Prasetyawan, and A. Amarudin, "Sistem keamanan pintu menggunakan sensor sidik jari berbasis mikrokontroller Arduino UNO R3," Jurnal Teknik dan Sistem Komputer, vol. 2, no. 1, pp. 121-135, 2021, doi: 10.33365/jtikom.v2i1.111.
A. A. Matarru, "Studi eksperimen Arduino Uno sebagai pengendali kursi roda elektrik," Journal of Informatics Information System Software Engineering and Applications (INISTA), vol. 4, no. 2, pp. 21-31, 2022, doi: 10.20895/inista.v4i2.499.
Y. Murdianingsih and L. Aprianti, "Sistem monitoring pengering sepatu berbasis Internet of Things pada platform Node-Red," Jurnal Teknologi Informasi dan Komunikasi, vol. 14, no. 1, 2021.
M. R. Ramadhan, "Rancang bangun box pengering sepatu berbasis mikrokontroler," Electrician: Jurnal Rekayasa dan Teknologi Elektro, vol. 17, no. 3, pp. 292-297, 2023, doi: 10.23960/elc.v17n3.2544.
M. R. Ramdan, T. Akbar, and H. M. Putra, "Sistem monitoring pengering sepatu otomatis berbasis IoT," Jurnal PRINTER: Jurnal Pengembangan Rekayasa Informatika dan Komputer, vol. 1, no. 1, pp. 43-52, 2023, doi: 10.29408/jprinter.v1i1.7207.
D. Khoirunnisak, "Sistem kendali temperatur pada alat pengering sepatu berdasarkan sensor limit switch," Tugas Akhir Diploma, Politeknik Negeri Jakarta, Jakarta, 2023.
A. L. N. P. Pratama, "Sistem kendali temperatur pada alat pengering sepatu berdasarkan sensor limit switch," Tugas Akhir Diploma, Politeknik Negeri Jakarta, Jakarta, 2023.
R. S. Pressman, Rekayasa Perangkat Lunak (Pendekatan Praktisi), Yogyakarta: Penerbit ANDI, 2012.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
