Pengaruh Penambahan Serat Kawat Bendrat pada Beton Mutu Tinggi terhadap Kapasitas Kuat Tekan dan Kuat Lentur

krisna bagus, Eddy Purwanto, Bayzoni bayzoni

Abstract


Concrete is one of the construction materials that has the advantage of being able to withstand a high compressive strength but has a low tensile strength.To overcome the weaknesses that exist in the concrete, one of the efforts applied is to add fiber in the form of bendrat wire in the concrete in order to increase the tensile strength and flexural strength of concrete. The specimens of this research are concrete cylinder with diameter 15 cm and height 30 cm and concrete beam object with dimension of length, width and height 60 cm, 15 cm, and 15 cm respectively. Tests were performed at 28-days of concrete. While the addition of bendrat wire fiber is done based on the percentage of volume fraction (Vf) addition to the volume of concrete by 0%; 0,299%; 0,695%; and 0,990%. Each variation was made 9 test specimens consisting of 6 cylinders and 3 beams.

The average compressive strength in high quality concrete without bendrat wire has the highest value of 50,0118 MPa. For the average compressive strength value at Vf 0.299%, 0.695%, and 0.990% were 42,2741 MPa, 41,8967 MPa and 39.6320 MParespectively. While for splitting strength and flexural strength in high quality concrete with volume fraction (Vf) 0,990% has the highest value with the splitting strength of an average of 4,6945 MPa and the average flexural strength of 7,9133 MPa

 

Keyword : High quality concrete, bendrat wire fiber


References


ACI 544 1R-96, 2002, State of the Art Report on Fiber Reinforced Concrete, ACI Committe 544.

Antoni, P., 2007, Teknologi Beton, Yogyakarta, Andi Offset.

Henager, C.N., and Doherty, T.J., 1976, Analysis of Reinforced Fibrous Concrete Beams, Journal of the Structural Division, ASCE, V. 102, No. ST!, pp, 177-188.

SNI 03-2834, 2000, Tata Cara Pembuatan Rencana Campuran Beton, Badan Standarisasi Nasional.

SNI 1974, 2011, Cara Uji Kuat Tekan Beton dengan Benda Uji Silinder, Jakarta, Badan Standarisasi Nasional.

SNI 4431, 2011, Cara Uji Kuat Lentur Beton Normal dengan Dua Titik Pembebanan, Jakarta, Badan Standardisasi Nasional.

SNI T-15, 1991, Tata Cara Perhitungan Struktur Beton Untuk Bangunan Gedung, Standar SNI T-15-1991-03, Yayasan LPMB Departemen Pekerjaan Umum, Bandung.

Soroushian, P., And Bayasi, Z.,1987, Concept Of Fiber Reinforced Concrete, Proceeding Of The International Seminar On Fiber Reinforced Concrete, Michigan State University, Michigan, USA.

Suhendro, B., 1991, Pengaruh Fiber Kawat Lokal Pada Sifat-sifat Beton, Laporan Penelitian, Lembaga Penelitian UGM, Yogyakarta.

Swamy, R.N., and Al-Ta'an, S.A., 1981, Deformation and Ultimate Strength in Flexure of Reinforced Concrete Beams Made with Steel Fiber Concrete, ACI Journal, Proceeding V. 78, No. 5, pp, 395-405.

Purwanto, E., 1999, Pengaruh Fiber Lokal pada Perilaku dan Kuat Torsi Ultimit Balok Beton Bertulang, Yogyakarta, Program Pasca Sarjana Universitas Gadjah Mada.

Tjokrodimuljo, K., 2012, Teknologi Beton, Yogyakarta, Biro Penerbit KMTS FT UGM.


Refbacks

  • There are currently no refbacks.


ISSN: 2303-0011