Pengaruh Bottom Ash sebagai Bahan Pengganti Sejumlah Pasir Terhadap Kuat Tekan, Kuat Lentur dan Modulus Elastistas Beton Mutu Tinggi
DOI:
https://doi.org/10.23960/jrsdd.v5i2.625Abstract Views: 120 File Views: 0
Abstract
Abstract
Over time the production of high strength concrete it will increse more and more and otherwise it will decrease the natural resources. One of them is sand as concrete material. Based on the problem, it will be required another material, that can replace a number of the sand. Bottom ash is one of material from waste coal plant, generally have particle size or fine granule like as sand. This research is used to determine the variation of sand and bottom ash for high strength concrete. The testing are compressive strength with cylinder concrete 10x20 cm, flexural strength with beam concrete 10x10x40 cm, and modulus of elasticity concrete with cylinder concrete 15x30 cm. The compositions of the bottom ash for substitution the sand are 0%, 20%, 40%, 60%, 80% and 100%. The results of the compressive strength and flexural strength optimum testing are showed on variation 80% of bottom ash. Compressive strength values are 39,68 MPa (7 days age) and 45,41 MPa (28 days age). Flexural strength values are 4,62 MPa (7 days age) and 5,53 MPa (28 days age). Modulus of elasticity concrete optimum are showed on variation 20% and 80% of bottom ash with 60625,67 MPa and 59441,67 MPa (28 days age).
Keywords : high strength concrete, bottom ash, compressive strength, flexural strength, modulus of elasticity concrete.
Abstrak
Seiring berjalannya waktu produksi beton mutu tinggi semakin lama akan semakin meningkat dan sebaliknya akan mengakibatkan berkurangnya sumber daya alam. Salah satunya ialah pasir sebagai bahan baku beton. Berdasarkan permasalahan tersebut, maka diperlukan suatu material lain yang dapat menggantikan sebagian sumber daya alam tersebut. Bottom ash merupakan salah satu material dari limbah hasil proses pembakaran batubara pada sektor pembangkit listrik, umumnya memiliki ukuran partikel atau butiran yang halus seperti pasir. Penelitian ini dilakukan untuk menentukan penggunaan variasi pasir dan bottom ash yang baik bagi beton mutu tinggi. Pengujian berupa uji kuat tekan dengan silinder beton 10x20 cm, uji kuat lentur dengan balok 10x10x40 cm dan modulus elastisitas beton dengan silinder beton 15x30 cm. Komposisi penggantian pasir dengan bottom ash sebanyak 0%, 20%, 40%, 60%, 80% dan 100%. Hasil pengujian kuat tekan dan kuat lentur optimum diperoleh pada variasi 80%bottom ash. Nilai kuat tekan sebesar 39,68 MPa (umur 7 hari) dan 45,41 MPa (umur 28 hari). Nilai kuat lentur sebesar 4,62 MPa (umur 7 hari) dan 5,53 MPa (umur 28 hari). Nilai modulus elastisitas beton optimum diperoleh pada variasi 20% dan 80% bottom ashyaitu sebesar 60625,67 MPa dan 59441,67 MPa (umur 28 hari).
Kata kunci : beton mutu tinggi, bottom ash, kuat tekan, kuat tarik lentur, modulus elastisitas beton
Downloads
References
ACI Committe 211, 1993, Guide for Selecting Proportions for High-Strength Concrete with Portland Cement and Fly Ash, Reapproved 1998, Detroit, 13 hlm.
ACI Committe 363, 1992, State of The Art Report on High-Strength Concrete, Reapproved 1997, Detroit, 55 hlm.
Annual Book of ASTM Standards Volume 04-0, 2001, Concrete and Aggregates, American Society for Testing and Materials, West Conshohocken PA.
Hertika, 2014, Pengaruh Bottom Ash Sebagai Bahan Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan dan Porositas Beton, Fakultas Teknik, Universitas Lampung, Bandar Lampung, 85 hlm.
Murdock, L.J, K.M Brook dan Stephanus Hendarko, 1999, Bahan dan Praktek Beton, Ed ke-4, Jakarta: Penerbit Erlangga, 473 hlm.
SNI 03-1974, 1990, Metode Pengujian Kuat Tekan Beton, Badan Standardisasi Nasional, Jakarta, 17 hlm.
SNI 15-2049, 2004, Semen Portland, Badan Standardisasi Nasional, Jakarta, 132 hlm.
SNI 2847, 2013, Persyaratan Beton Struktural Untuk Bangunan Gedung, Badan Standardisasi Nasional, Jakarta, 265 hlm.
SNI 4431, 2011, Cara Uji Kuat Lentur Beton Normal dengan Dua Titik Pembebanan, Badan Standardisasi Nasional, Jakarta, 16 hlm.
SNI Pd T-04-2004-C, 2004, Tata Cara Pembuatan dan Pelaksanaan Beton Berkekuatan Tinggi, Departemen Permukiman dan Prasarana Wilayah, Bandung, 13 hlm.
Tjokrodimuljo, Kardiyono, 2012, Teknologi Beton, KMTS FT UGM, Yogyakarta.
Additional Files
Published
How to Cite
Issue
Section
License
JRSDD is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.